The specified privilege ID is out of range. −1967345149 Invalid access type. After the reference is opened, that VI can return the reference to other VIs that could not normally open the reference. 1396 Cannot convert text from the source character set to Attempted to read from or write to a file of a type incompatible with the operation. This error can occur if you attempt to edit a VI that is running or reserved for running. Source
Verify that the VI is marked to save its compiled code separately and that it is not broken. Reading after this sequence should work correctly.Your block diagram should appear as shown below: 2. or (OS X/Linux) < > \ | : " * ?. 1617 LabVIEW is unable to generate a VI comparison report. Poor|Excellent Yes No Document Quality? http://zone.ni.com/reference/en-XX/help/371361J-01/lverror/misc_lv_error_codes/
Select File»Open to open the VI and verify that you can run it. This could be caused by an invalid sound driver. 4801 Invalid sound task refnum. Try freeing up disk space or saving to a different disk or drive.
If you do not have the right amount of data to align to a sector size, you must pad the data with filler data and delete the filler data before LabVIEW It must be loaded and saved in the current version of LabVIEW. 1453 You may only set the vertical arrangement on a label, caption or free label. 1454 LabVIEW classes cannot The specified wave format is not supported. Labview Error 1073807339 This error also might occur if the VI is a polymorphic VI, which cannot be loaded in the LabVIEW Run-Time Engine.
You must have DIAdem 9.1 Service Pack 2 or later installed to use the DIAdem Report Express VI. −2580 The Write to Measurement File Express VI cannot append new data to Daqmx Error Codes You cannot use this property with a Conditional Disable structure because conditions determine the active frame. No reference could be returned. http://digital.ni.com/public.nsf/allkb/FD9FEFCDD2F95C29862572AA006AC909 This is usually due to a required driver not being installed on the system.
To run a VI using a static VI reference, use an Invoke Node to call the Run VI method. Labview Error 200279 The file might have been moved or deleted, or the file path might be incorrectly formatted for the operating system. A valid path cannot contain any of the following characters: (Windows) < > / | : " * ? To correct this error and inline the subVI, remove the implicit Property Node or Invoke Node. 1488 The migration file cannot load because it is no longer supported. 1489 The migration
Poor|Excellent Yes No Document Quality? http://digital.ni.com/public.nsf/allkb/F3E0621CB71AA16786256F970000FC57 You also can use the Front Panel:Open method to open the front panel programmatically. 1002 The VI cannot run because it has a front panel control in an error state. 1003 Labview Visa Error -1073807339 This can result in a temporary phase shift, which would alter the update period for NI Scan Engine variables for one iteration. Labview Error Daqmx For example, enter 5008.
Sync up changes before attempting this operation. 1500 If you obtain a user event reference in one application instance, you cannot use that user event reference in another application instance. Refer to the specific function or VI reference topic in the LabVIEW Help for information about overwriting files or folders. 11 Too many files open. 12 Some system capacity necessary for Wait until the VI is not being modified to get the image of a panel or diagram. 1001 The VI front panel is not open. Answered Your Question? 1 2 3 4 5 Document needs work? Labview Visa Error Codes
A timeout error occurred because the application was unable to successfully acquire a mutex. 4823 You cannot perform this operation without an active task. A filename is no longer sufficient because the full name of a VI now includes any owning libraries. Add Comments 1 2 3 4 5 My Profile|Privacy|Legal|Contact NI© National Instruments Corporation. If you receive this error while using a File I/O function or VI, you may be attempting to overwrite a file or folder that already exists.
Each byte has a specific format with a start bit, data bits, parity, and stop bits. Labview Custom Error Codes This might be due to an error freeing internal or OS resources, a failed network connection, or a lower level driver or OS error. −1073807333 Specified degree is invalid. −1073807332 Specified If you receive this error while developing a large application or storing large sets of data in LabVIEW, refer to the KnowledgeBase at ni.com for more information. 4 End of file
The project has a locked untitled dependency. You may be experiencing noise on your serial line. To run a VI using a static VI reference, use an Invoke Node to call the Run VI method. Labview Fpga Error Code If this error is returned from the Open VI Reference function on a remote connection, use the VI Server page of the Options dialog box to ensure that the VI is
Try freeing up disk space or saving to a different disk or drive. 10 Duplicate path. 11 Too many files open. 12 Some system capacity necessary for operation is not enabled. Ensure that the parameters values are within the supported range for the hardware and drivers. −4406 A VI item in the palette data array is not supported in this version of The frequency for a data point is then calculated as f0+N*df. You can use the Strip Path function to wire the filename as a string, but this will not work for VIs in libraries. 1447 There was a name conflict while saving
To correct this error, you must obtain a valid license for the VI and its containing library. 1390 You attempted to open a VI Server reference to an out-of-scope VI. If you do not have the right amount of data to align to a sector size, you must pad the data with filler data and delete the filler data before LabVIEW Verify the values you wired to the Call Library Function Node. 1098 Cannot disconnect type definitions or polymorphic VIs if the block diagram is not available. 1100 No object of that You must create these objects in the LabVIEW development system. 1124 VI is not loadable.
Attempted to read from or write to a file of a version incompatible with the write/read function version. To correct this error, make sure the reference to the semaphore is valid. 1544 LabVIEW attempted a read, write, or seek on a file opened in unbuffered mode, and the data To resolve this error, give the file a path that does not already contain a LabVIEW file in any open application instance. 1358 The splitter bar cannot be moved to this If you receive this error while trying to write to the Strings and Values  property of a control, refer to the KnowledgeBase at ni.com for more information. 1130 The VI